Watts Fleck 7000 Plastic Valve Manuel d'utilisateur

Model 7000Service Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference

Programming a Meter Delayed Regenerated SystemPage 103. EXTENDED Programming Mode Regeneration Cycle Step Programming (Display Code 1 to 6) Use thi

1. Feed water hardness (Display Code H) The feed water hardness setting displays only if the system is set to operate as a Meter Immediate or Meter

Page 12Programming a Meter Immediate Regeneration System3. Extended Diagnostics Mode (Viewable Only) (Dy xx) Display Code xx = days since last Regen

Page 13Programming a Time Clock Regeneration System3. Extended Programming Mode Regeneration Cycle Step Programming (Display Code 1 – 6) This Progr

Page 1Programming a Day of the Week Regenerated System3. Individual Day of the Week Regeneration Setting — Set to 1 or 0 using the Set Up and Set

Page 15Programming a Day of the Week Regenerated System1. Extended Programming Mode Regeneration Cycle Step Programming (Display Code 1 – 6) Use th

Page 16Water Conditioner Flow DiagramsIn Service PositionBackwash Position

Page 17Water Conditioner Flow DiagramsBrine PositionSlow Rinse Position

Page 18Water Conditioner Flow DiagramsRapid Rinse PositionBrine Tank Rell Position

Page 19Notes

Job Specication Sheet ...

Page 20Power Head Assembly

Page 21Power Head Assembly Parts List Item No. Quantity Part No. Description 1 ...1 ... 40968 ...

Page 22Valve Assembly Item No. Quantity Part No. Description 1 ...1 ... 61050 ... Valv

Page 23Valve Assembly Parts List Item No. No. Req’d Part Number Description Part No. Injector No. 615-

Page 2Bypass AssemblyIMPORTANTTo bypass the valve, turn bypass knob on bothsides of the valve to bypass position.When returning to service, put the i

Page 252310 Safety Brine ValveItem No. Quantity Part No. Description 1 ... 1 ... 60014 ... Safety B

Page 26TroubleshootingWARNINGThe controller MUST be depressurized before removingany quick connection clips for servicing. The connectorshould be push

Page 27TroubleshootingProblem Cause Correction3. Unit uses too much salt. A. Improper salt setting.B. Excessive water in brine tank.A. Check salt usag

Page 28Removing Gear Box Assembly1. Unplug the power source.2. With 3/8” nut driver, turn the cycle cam counter-clockwise to the position shown in i

Page 29Inserting Circuit Board1. To insert the circuit board, align the notches on the left side of the board with the exible nger on the power

Job Number: Model/Serial Number: Water Test: Capacity Of Unit: Max: Per Regeneration:Brine Tank Size:Salt Setting per Regeneration:Treated Wa

Page 30Connecting the Circuit Board141033CDF253-0AA1C14C3B1B241033-2DF254-0D2D1After the circuit board is installed:1. Connect the motor wires (A) to

Page 31Dimensions41023_REVC.pdf

Page 32Meter Flow Data7000 Valve035202510150)DISP( porD erusserP05015102520353045405Service Flow (GPM) renetfos 35781RT retliF 88681RT 41140-02Softene

Page 33Injector Flow DataA) Total Flow, 3/8" Brine System C) RinseB) Total Flow, 1/2" Brine Line D) Brine Draw, 3/8" Brine SystemE) Bri

Page 3Notes

Page 35Notes

P/N 1028 Rev. E /06

Water Pressure A minimum of 20 psi inlet water pressure is required for regeneration valve to operate effectively.Electrical FacilitiesAn uninterrupte

Installation Instructions1. Place the softener tank where you want to install the unit. NOTE: Be sure the tank is level and on a rm, clean base.2.

Time Clock or Day of the Week Regeneration ValvesIn normal operation the Time of Day Display may be viewed at all times. The control operates for a pr

Flow Meter Equipped Valves – Delayed Regeneration ModeIn Normal operation the Time Of Day display alternates with the Volume Remaining display. The o

Set Time of Day • Press the Set Up and Set Down buttons to set time of day. — Metric = 2 hour clock — US = 12 hour clock with PM indicator

1. Feed water hardness (Display Code H). NOTE: The feed water hardness setting only displays when the system is set to operate as a Meter Immediat