Watts PIPF Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Watts PIPF. Watts PIPF User Manual Manuel d'utilisatio
- Page / 1
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Watts Series PIPF
Isolation Pump Flange with Purge Port
and Swivel Flange
Series PIPF Pump Flanges are designed to simplify the installa-
tion, service and removal of pumps and circulators in hydronic
systems. PIPF pump flanges feature a purge port which allows
system purging at the pump or circulator. PIPF pump flanges
also feature a swivel flange, which allows you to rotate the valve
body so you can put the purge port in the best position for your
application.
Installation
To install simply bolt the PIPF flange to the return side of the
pump/circulator flange. Be sure that there is a pump gasket
between each flange. Contact your wholesaler if you require a
gasket.
1. Bolt the PIPF flange to the return side of the pump/circulator
flange.
STOP! Do not install the PIPF flange without a pump gasket.
2. Tighten the bolts joining the PIPF flange to the pump flange,
taking care not to over-tighten. Hand-tighten and
1
⁄2" turn is
recommended.
3. When the system is filled, inspect for leaks at the flange.
Tighten the bolts as needed, taking care not to over-tighten.
4. For solder models only, slip the plastic tether on the purge
port over the slotted ball valve to protect tether from heat
applied during soldering.
IS-PIPF 0845 EDP# 1915927 ©Watts Regulator Co., 2008
For Solder Models
This valve is designed to be soft soldered into lines without dis-
as sem bly, using a low temperature solder 420°F (216°C). Other
sol ders such as 95/5 tin antimony 460°F (238°C) or 96/4 tin
silver 430°F (221°C) can be used, however extreme caution must
be used to prevent seal damage. Higher temperature solders will
dam age the seat material. ANSI B16.18 states that the maximum
operating pressure of 50-50 solder connections is 200psi (13.8
bar) at 100°F (38°C), and decreases with higher temperatures.
Apply heat with the flame directed AWAY from the center of the
valve body. Excessive heat can harm the seats.
Purging the Hydronic System
1. I solate all circuits by shutting the isolation or zone valve and
the PIPF shutoff valves. Remove cap from purge port.
2. Starting with one circuit, attach a hose to the purge port of
the PIPF. (Note: A hose must be run into a suitable floor drain
or run to the outside to accommodate purged water).
3. Open the PIPF’s purge port by turning the brass screw
1
⁄4
turn, and open the isolation or zone valve.
4. Then open the make up water or boiler fill valve’s fast fill
feature. Allow water to flow through the PIPF’s purge port
until the water runs clear and free of air bubbles.
5. Close the make up water or boiler fill valve.
6. Next close the PIPF purge port by turning the brass screw
1
⁄4
turn until the water stops flowing. Shutoff the isolation or zone
valve. Replace cap on purge port.
7. Repeat steps 2 – 6 for each zone.
8. Upon completion of purging all zones of air, open the PIPF
shut off valve.
Watts PIPF
Shut Off Valve
Purge Port
Watts IPF
Gaskets Not
Supplied
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
Water Safety & Flow Control Products
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of
original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting
from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no
control. This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
1
Résumé du contenu
Page 1 - Watts Series PIPF
Watts Series PIPFIsolation Pump Flange with Purge Port and Swivel FlangeSeries PIPF Pump Flanges are designed to simplify the installa-tion, service a
Plus de documents pour Accessoires pour l'eau Watts PIPF
Watts PIPF Manuel d'utilisateur
(2 pages)
Produits connexes et manuels pour Accessoires pour l'eau Watts PIPF
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.708 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels