Watts WP9S Manuel d'utilisateur télécharger pdf

Watts WaterPEX

Installation Guidelines

Product Overview

The CinchClamp

™

should be installed in accor-

dance to local plumbing code and practices.

In addition to these standards, the following

should be considered:

Tools:

Use an approved tool such as Watts

CinchTool

™

or equivalent (must be ratchet-

ing-type tool meeting ASTM 2098 specifi-

cations). Failure to use this type of tool will

result in an improper fit. Use of other tools,

such as pliers, will result in an improper fit

and possible leaks.

Warning!

• Ifconnectionsmustbemadeintempera-

tures below 30°F, caution must be taken

to allow the WaterPEX to form a proper

seal against the barb. Apply the connec-

tion slowly to ensure the PEX material

conformstothebarb.

• WhentheCinchTool’sjawsareclosed,the

gap between the jaws must be less than

⁄16”.Anygapgreaterthan

⁄16”isasignof

toolwear.Discardthetoolandreplaceit

immediately. Use of an out-of-spec tool

willcauseleaks.

• Never use a CinchTool

™

 to remove a

CinchClamp

™

. Damage to the tool’s cali-

brationmayresult.Useapairofpliersor

vicegrips.

Making WaterPEX

Connections with CinchClamps™ & Close Ear CinchClamp

Step 3:

Step 4:

Step 2:

Step 1:

The Connection

Make sure the WaterPEX

has a clean,

square end. Use a WaterPEX

Tube Cutter

to ensure the WaterPEX

does not deform

while cutting.

For CE™ CinchClamps:

WaterPEX connections made with Close

Ear (CE) CinchClamps are a snap. Place the

Close Ear CinchClamp over the end of the

pipe. It stays where you put it! Follow steps

1 through 4 and allow the same

⁄8" gap

between the shoulder of the tting and the

CinchClamp.

Step 1:

Slide the CinchClamp

™

over the end of the

WaterPEX

. Allow enough room for the fitting

to be inserted.

Step 2:

Insert the fitting into the tube end making

sure the tube is fully sealed over the fit-

ting. Allow for

⁄8” of clearance between the

CinchClamp™ and the fitting.

Warning: Never use CinchClamps

™

 on

PEX fittings made from copper. Leaks

mayresult.UseonlyASTMbrassorpoly-

sulfonecrimpinsertfittings.

Step 3:

Position the open jaws of the CinchTool

™

over the tab of the CinchClamp

™

and com-

press the handles of the CinchTool together.

The ratcheting mechanism of the CinchTool

™

will not allow for an improper connection.

The CinchTool

™

will automatically release

when the connection is complete.

Step 4:

Verify the connection is secure by visually

checking the CinchTab

™

. The tab should be

shaped as shown in Step 4.

IS-WP-CinchClampGuidelines

1 2

Résumé du contenu

Page 1 - Installation Guidelines

Watts WaterPEX® Installation GuidelinesProduct OverviewThe CinchClamp™ should be installed in accor-dance to local plumbing code and practices. In add

Page 2

LIMITED WARRANTY: A. Watts Regulator Co. (ìWattsî) warrants its WaterPEX® cross-linked polyethylene tubing, barbed PEX fittings, brass and plastic Qui

Modèles reliés WP8SK

Plus de documents pour Accessoires pour l'eau Watts WP9S

Voir le document Watts WP9S Manuel d'utilisateur

Watts WP9S Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Watts WP9S Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Watts WP9S. Watts WP9S User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés WP8SK

Plus de documents pour Accessoires pour l'eau Watts WP9S

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Watts WP9S