Watts WPCCT-6 Manuel d'utilisateur télécharger pdf

For Residential and Commercial Applications

ES-WP-WPCCT-6

Job Name

–––––––––––––––––––––––––––––––––––––––––––

Contractor

––––––––––––––––––––––––––––––––––––––––––––

Job Location

–––––––––––––––––––––––––––––––––––––––––

Approval

–––––––––––––––––––––––––––––––––––––––––––––

Engineer

–––––––––––––––––––––––––––––––––––––––––––––

Contractor’s P.O. No.

–––––––––––––––––––––––––––––––––––

Approval

–––––––––––––––––––––––––––––––––––––––––––––

Representative

––––––––––––––––––––––––––––––––––––––––

Ratcheting CinchClamp™ Tool with work pouch and calibration gauge.

Calibration gauge is located in side pouch.

MODEL DESCRIPTION

WPCCT-6 Ratcheting CinchClamp™ Tool

Model WPCCT-6

Ratcheting CinchClamp™ Tool

Sizes:

⁄2",

⁄8",

⁄4", 1" (15, 18, 20, 25mm)

Watts Ratcheting CinchClamp™ Tool is designed to be used

with WaterPEX tubing and CinchClamp™ connections.

Specifications

Connections shall use Watts brass and poly-alloy crimp fittings

and WaterPEX

cross-linked polyethylene pipe.

Installation

All CinchClamps must be installed using a Watts CinchClamp

Tool and in accordance with all installation guidelines.

– Make sure the WaterPEX has a clean, square cut end.

– Slide the CinchClamp over the WaterPEX.

– Insert fitting and position CinchClamp, allowing for approxi-

mately

⁄8" clearance between clamp and fitting.

– Position the open jaws of the CinchClamp™ Tool over the

tabs of the CinchClamp and squeeze. Allow the tool to ratch-

et to the next position. Repeat until the white indicator is

completely visible in the view hole (approximately seven

times).

– To release the CinchClamp Tool rotate the release lever on the

side. It is very important to complete the cinch process

before releasing the tool.

If connections are made in temperatures below 30°F,

caution must be taken to pause between ratchets, allow-

ing the WaterPEX to form a proper seal against the barb.

Do not use the Ratcheting CinchClamp Tool to remove

CinchClamps. This will cause damage to the tool,

resulting in improper connections.

Standards

– Watts CinchClamps are manufactured in accordance with the

American Society for Testing and Materials (ASTM) F-2098.

– Watts fittings are manufactured in accordance with the

American Society for Testing and Materials (ASTM) F-1807,

F-2159, and F-2434.

Holster

Ratcheting

CinchClamp™ Tool

View Hole

Gauge

Release Lever

Gauge

Pouch

Model WPCCT-6

Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,

please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with-

out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.

1 2

Model WPCCT-6 1
Calibration 2

Résumé du contenu

Page 1 - Model WPCCT-6

For Residential and Commercial ApplicationsES-WP-WPCCT-6Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor –––––––––––––––––––––––––

Page 2 - Calibration

CalibrationDo not use the Ratcheting CinchClamp™ Tool if it has been damaged as this may result in an improper cinch.After repeated use of the CinchCl

Commentaires sur ces manuels

Pas de commentaire

Watts WPCCT-6 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Watts WPCCT-6. Watts WPCCT-6 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Watts WPCCT-6